http://www.service.com/doccenter/ansi_standards.html (World Wide Web Directory, 06/1995)Published Bi-Weekly by the American National Standards Institute, 11 West 42nd Street, New York, NY 10036
Volume 24, #24, November 26, 1993
Copyright 1994 by American National Standards Institute, Inc.
ANSI members may reproduce for internal distribution. Journals may excerpt items in their fields.
ISSN 0038-9633
NOTE: This is a sample draft only and contains only excerpts from this issue.
(Introduction and Ordering Instructions)
# = Safety Standard, * = Standard for Consumer Products
Comment deadline: January 25, 1994
ACOUSTICS
BSR S3.5, Methods for the Calculation of the Speech
Intelligibility Index (revision of ANSI S3.5-1969 (R1986))
Defines a method for computing a physical measure, called
the Speech Intelligibility Index or SII, that is highly
correlated with the intelligibility of speech as evaluated
by speech perception tests given a group of talkers and
listeners.
Single copy price: $30.00
(See order and comment instructions at end of category.)
BSR S1.43, Specification for Integrating-Averaging Sound
Level Meters (new standard)
Describes instruments for the measurement of frequency-
weighed and time-average sound pressure levels. Optionally,
sound exposure levels may be measured. This standard is
consistent with the relevant requirements of Specification
for Sound Level Meters, ANSI S1.4-1983, but specifies
additional characteristics that are necessary to measure the
equivalent continuous sound pressure level of steady,
intermittent, fluctuating, and impulsive sounds.
Single copy price: $30.00
Order from: Acoustical Society of America
ANTENNAS
#BSR/UL 150, Antenna Rotators (revision of ANSI/UL 150-1989)
Covers antenna rotators intended for household and
commercial use on supply circuits in accordance with the
American National Standard National Electrical Code,
ANSI/NFPA 70-1993. This standard does not cover systems
that use a stationary antenna and change or rotate the
receiving pattern by electronic or switching means.
Single copy price: Free
Order from: Underwriters Laboratories, Inc.
Attn: Bernadette Folan
333 Pfingsten Road, Northbrook, IL 60062-2096
Send comments (with copy to BSR) to: Same
BATTERIES
BSR/UL 218A, Battery Contactors for Use in Diesel Engines
Driving Centrifugal Fire Pumps (revision of ANSI/UL 218A-
1987)
Covers battery contractors for use in the starting systems
of diesel engines driving centrifugal fire pumps, rated 50
volts maximum, in accordance with the Standard for
Centrifugal Fire Pumps, ANSI/NFPA 20-1990.
Single copy price: Free
Order from: Underwriters Laboratories, Inc.
Attn: Susan Gill
333 Pfingsten Road, Northbrook, IL 60062-2096
Send comments (with copy to BSR) to: Same
CHEMICALS
#BSR Z129.1, Hazardous Industrial Chemicals Precautionary
Labeling (revision of ANSI Z129.1-1988)
Establishes guidelines and applies to the preparation of
precautionary labeling of hazardous chemicals used under
industrial occupational conditions.
Single copy price: $18.00
Order from: Chemical Manufacturers Association
Attn: Mary Beth Preston
2501 M Street, NW
Washington, DC 20037
Send comments (with copy to BSR) to: Suzanne D. Croft, CMA
COMPRESSORS
#BSR/ASME B19.1b, Safety Standard for Air Compressor Systems
(supplement to ANSI/ASME B19.1-1990 and ANSI/ASME B19.1a-
1991)
Addresses all aspects of air compressor systems from the
entrance to the inlet device through the compressor and
associated heat exchangers, dryers, and pulsation
suppression devices to the point of entry to the
distribution system.
Single copy price: $9.00
(See order and comment instructions at end of category.)
#BSR/ASME B19.3a, Safety Standard for Compressors for
Process Industries (supplement to ANSI/ASME B19.3-1991)
Provides general information on safe practices and specific
recommendations covering basic safety requirements for
compressors used in the process industries.
Single copy price: $9.00
Order from: American Society of Mechanical Engineers
Attn: Silvana Rodriguez-Bhatti, 39G
345 East 47th Street, New York, NY 10017
Send comments (with copy to BSR) to: Melissa Aranzamendez,
ASME, 39C
TRANSMITTERS
BSR/UL 632, Electrically Actuated Transmitters (revision of
ANSI/UL 632-1989)
Covers electrically actuated transmitters intended for
permanent installation and use in ordinary indoor locations
in accordance with ANSI/NFPA 71, NFPA 72A, NFPA 72B, NFPA
72C, and NFPA 72D.
Single copy price: Free
Order from: Underwriters Laboratories, Inc.
Attn: Michael Hieb
1655 Scott Boulevard, Santa Clara, CA 95050-4169
Send comments (with copy to BSR) to: Same
TURBINE GENERATORS
BSR/NEMA SM 24, Land-Based Steam Turbine Generator Sets 0 to
33,000 kW
Covers single-stage and multistage steam turbines, reduction
gears, air-cooled electric generators, switchgear, and
auxiliary systems. Applicable to turbines expanding various
gases or compressed air. Applies to auxiliary equipment
associated with turbine generator, such as governors,
baseplates, excitation controls, steam piping, etc. Does
not apply to other equipment in steam cycle or electrical
distribution systems.
Single copy price: $33.00
Order from: National Electrical Manufacturers Association
Attn: Publications Orders
2101 L Street, NW, Suite 300
Washington, DC 20037
Send comments (with copy to BSR) to: John Gauthier, NEMA
VEHICLES, SURFACE
#BSR/ASME B56.6a, Safety Standard for Rough Terrain Forklift
Trucks (supplement to ANSI/ASME B56.6-1992)
Defines safety requirements relating to the elements of
design, operation, and maintenance of rough terrain forklift
trucks.
Single copy price: $20.00
Order from: American Society of Mechanical Engineers
Attn: Silvana Rodriguez-Bhatti, 39G
345 East 47th Street, New York, NY 10017
Send comments (with copy to BSR) to: William Berger, 39D
ASME
(Introduction)
ABRASIVES
ANSI B74.3-1993, Specifications for Shapes and Sizes of
Diamond or CBN Abrasive Products (revision of ANSI B74.3-
1986)
Approval date: September 29, 1993
ANSI B74.11-1993, Specifications for Tumbling Chip Abrasives
(revision of ANSI B74.11-1986
Approval date: November 2, 1993
ACCESS CONTROL
ANSI/UL 294-1993, Access Control System Units (revision of
ANSI/UL 294-1986)
Approval date: October 11, 1993
AGRICULTURAL EQUIPMENT
ANSI/ASAE EP282.2-FEB93, Design Values for Emergency
Ventilation and Care of Livestock and Poultry (new standard)
Approval date: September 29, 1993
TELECOMMUNICATIONS
ANSI T1.508a-1993, Network Performance Supplement to Loss
Plan for Evolving Digital Networks (supplement to ANSI
T1.508-1992)
Approval date: October 11, 1993
ANSI T1.632-1993, ISDN Supplementary Service Normal Call
Transfer (new standard)
Approval date: November 2, 1993
TELEVISION
ANSI/SMPTE 259M-1993, Television 10-Bit 4:2:2 Component
and 4fsc NTSC Composite Digital Signals Serial Digital
Interface (new standard)
ANSI/SMPTE 261M-1993, Television 10-Bit Serial Digital
Television Signals: 4:2:2 Component and 4fsc NTSC Composite
AMI Transmission Interface (new standard)
Approval date: October 11, 1993
TRANSMISSION CHAINS
ANSI/ASME B29.6M-1993, Steel Detachable Link Chains,
Attachments, and Sprockets (revision and redesignation of
ANSI B29.6M-1983)
ANSI/ASME B29.19-1993, A and CA550 and 620 roller Chains,
Attachments, and Sprockets (revision and redesignation of
ANSI B29.19-1976)
Approval date: September 29, 1993
STANDARDS WITHDRAWN
BIOACOUSTICS
ANSI S3.26-1981, Reference Equivalent Threshold Force Levels
for Audiometric Bone Vibrators (withdrawal)
Withdrawal date: November 2, 1993
FLUID POWER HYDRAULIC
ANSI B93.44-1978, Method for Extracting Fluid Samples from a
Reservoir of an Operating Hydraulic Fluid Power System
(withdrawal)
Withdrawal date: November 2, 1993
PHOTOGRAPHY FILM AND SLIDES
ANSI PH3.11-1953, Dimensions for Stereo Still Picture on
35mm Film (5-Perforation Format) (withdrawal)
Withdrawal date: November 2, 1993
PHOTOGRAPHY PAPER
ANSI PH1.64-1984, Dimensions for Paperboard Cores
(withdrawal)
Withdrawal date: November 2, 1993
PHOTOGRAPHY PROJECTION EQUIPMENT
#*ANSI PH3.61-1974 (R1982), Photographic Slide Projectors
for Consumer Use Safety Requirements (withdrawal)
ANSI PH3.69-1977, Temperature of Photographic Equipment
Method for Measuring (withdrawal)
Withdrawal date: November 2, 1993
APPROVAL SUSPENDED
CERTIFICATION
ANSI Z34.1-1993, Third-Party Certification Programs for
Products, Processes, and Services (revision of ANSI Z34.1-
1987)
An appeal has been filed in the ANSI decision of June 3,
1993, to approve the above referenced standard as an
American National Standard. Approval is, therefore,
suspended, pending adjudication of the appeal.
(Introduction and Ordering Instructions)
ISO DRAFT INTERNATIONAL STANDARDS
ACOUSTICS (TC 43)
ISO/DIS 8253-3, Acoustics Audiometric test methods Part
3: Speech audiometry February 28, 1994, $43.00
ISO/DIS 11689, Acoustics Systematic collection and
comparison of noise-emission data for machinery and
equipment February 28, 1994, $51.00
TRACTORS AND MACHINERY FOR AGRICULTURE AND FORESTRY (TC 23)
ISO/DIS 10627-2, Agricultural sprayers Data sheet Part
2: Technical specifications related to components February
28, 1994, $64.00
ISO/IEC JTC 1, INFORMATION TECHNOLOGY
ISO/IEC DIS 10035-2, Information technology Open Systems
Interconnection Connectionless ACSE protocol Part 2:
Protocol implementation conformance statement (PICS)
proforma March 11, 1994, $24.00
ISO/IEC DIS 10729-2, Information technology Open Systems
Interconnection Conformance test suite for the
presentation layer Part 2: Test suite structure and test
purposes for ASN.1 basic encodings March 11, 1994, $54.00
IEC DRAFT INTERNATIONAL STANDARDS
ELECTRICAL EQUIPMENT IN MEDICAL PRACTICE (TC 62)
62(Central Office)20 Draft IEC 1272, 1st edition, Guidance
on the application of EN 29001, EN 46001, EN 29002 and EN
46002 for the active (including active implantable) medical
device industry December 28, 1993, $51.00
LAMPS AND RELATED EQUIPMENT (TC 34)
34C(Central Office)275 Draft Amendment to IEC 923 Clause
20 of Section 4, Appendices B and D December 28, 1993,
$26.00
34B(Central Office)767 IEC 61-2: Lampholders. Creepage
distances and clearances. Amendments December 28, 1993,
$19.00
34B(Central Office)768 R7s and Rx7s caps/holders/gauges.
Amendments December 28, 1993, $26.00
34B(Central Office)769 IEC 61-4: Guidelines and general
information. International designation of lamp caps and
holders. Amendment December 28, 1993, $19.00
SWITCHGEAR AND CONTROLGEAR (TC 17)
17B(Central Office)218 Draft amendement to IEC 947-5-2:
Low-voltage switchgear and controlgear. Part 5: Control
circuit devices and switching elements. Section 2: Proximity
switches. Sub-clause 8.5.5: Testing for the frequency of the
operating cycle December 28, 1993, $21.00
(Introduction)
ISO STANDARDS
AGRICULTURAL FOOD PRODUCTS (TC 34)
ISO 1134: 1993, Pears Cold storage, $31.00
ISO 7932: 1993, Microbiology General guidance for the
enumeration of Bacillus cereus Colony count technique at
30oC, $33.00
WATER QUALITY (TC 147)
ISO 5667-7: 1993, Water quality Sampling Part 7:
Guidance on sampling of water and stream in boiler plants,
$43.00
ISO 9391: 1993, Water quality Sampling in deep waters for
macro-invertebrates Guidance on the use of colonization,
qualitative and quantitative samplers, $40.00
ISO TECHNICAL REPORT
MACHINE TOOLS (TC 39)
ISO TR 13618: 1993, Code of practice for the safe operation
of work-holding chucks used on lathes, $84.00
ISO/IEC JTC 1, INFORMATION TECHNOLOGY
ISO/IEC 9834-6: 1993, Information technology Open Systems
Interconnection Procedures for the operation of OSI
Registration Authorities: Application processes and
application entities, $28.00
ISO/IEC 10028: 1993, Information technology
Telecommunications and information exchange between systems
Definition of the relaying functions of a Network layer
intermediate system, $68.00
ISO/IEC 10164-6: 1993, Information technology Open Systems
Interconnection Systems Management: Log control function,
$46.00
IEC STANDARDS
AUTOMATIC CONTROLS FOR HOUSEHOLD USE (TC 72)
IEC 730-1: 1993, Automatic electrical controls for household
and similar use Part 1: General requirements, $232.00
ELECTRIC CABLES (TC 20)
IEC 811-1-1: 1993, Common test methods for insulating and
sheathing materials of electric cables Part 1: Methods for
general application Section 1: Measurement of thickness
and overall dimensions Tests for determining the
mechanical properties, $69.00
TOOLS FOR LIVE WORKING (TC 78)
IEC TECHNICAL REPORTS
IEC 1219: 1993, Live working Earthing or earthing and
short-circuiting equipment using lances as a short-
circuiting device Lance earthing, $98.00
ELECTRICAL EQUIPMENT IN MEDICAL PRACTICE (TC 62)
IEC 1288-1: 1993, Cardiac defibrillators Cardiac
defibrillators-monitors Part 1: Operation, $77.00
IEC 1288-2: 1993, Cardiac defibrillators Cardiac
defibrillators-monitors Part 2: Maintenance, $77.00
INSULATING MATERIALS
IEC 1244-1: 1993, Determination of long-term radiation
ageing in polymers Part 1: Techniques for monitoring
diffusion-limited oxidation, $98.00
INSULATORS
IEC 1245: 1993, Artificial pollution tests on high-voltage
insulators to be used on d.c.systems, $98.00
(Introduction and Ordering Information)
New proposals for European standards projects (for
information)
The following new proposals for European standards projects
have been sent to CEN members to enquire whether interest
exists in developing European Standards for these topics:
CEN N 1049, Castors and wheels: Terminology, method of test,
requirement and dimensions
European drafts sent for CEN enquiry
The following European drafts have been sent to CEN members
for enquiry and comment. If the draft is a proposed
adoption of an International Standard, it is so noted. The
final date for offering comments is listed after each
proposal. Copies are available from ANSI at the prices
indicated.
BUILDINGS
prEN 1190, Thermal performance of buildings Heat exchange
with the ground Calculation method February 28, 1994,
$84.00
prEN 33786, Thermal performance of building elements
Thermal inertia characteristics Calculation methods
(ISO/DIS 13786: 1993) March 15, 1994, $43.00
REFRIGERATING SYSTEMS AND HEAT PUMPS
prEN 378-4, Refrigerating systems and heat pumps Safety
and environmental requirements Part 4: Selection of
refrigerants February 28, 1994, $28.00
prEN 378-5, Refrigerating systems and heat pumps Safety
and environmental requirements Part 5: Design,
construction and materials February 28, 1994, $54.00
RUBBER HOSE AND HOSE ASSEMBLIES
prEN 1360, Rubber and thermoplastic hose and hose assemblies
for measuring fuel dispensing Specification March 15,
1994, $36.00
prEN 1361, Rubber hoses and hose assemblies for avaition
fuel handling Specification March 15, 1994, $68.00
WINDOWS, DOORS AND SHUTTERS
prEN 31077, Windows, doors and shutters Thermal
transmittance Calculation methods (ISO/DIS 11077: 1993)
March 15, 1994, $61.00
European drafts sent for formal vote (for information)
The following European drafts have been sent to CEN members
for formal vote. If the draft is a proposed adoption of an
International Standard, it is so noted.
FLOOR COVERINGS
prEN 425, Resilient floor coverings Determination of the
effect of a castor chair
prEN 427, Resilient floor coverings Determination of the
side length and squareness of tiles
prEN 430, Resilient floor coverings Determination of mass
per unit area
prEN 431, Resilient floor coverings Determination of peel
resistance
prEN 432, Resilient floor coverings Determination of shear
force
prEN 433, Resilient floor coverings Determination of
static indentation
prEN 434, Resilient floor coverings Determination of
dimensional stability and curling after exposure to heat
ROOFING TILES
prEN 538, Clay roofing tiles for discontinuous laying
Flexural strength test
prEN 539 1, Clay roofing tiles for discontinuous laying
Determination of physical characteristics Part 1:
Impermeability test
PIPING SYSTEMS
prEN 763, Plastics piping and ducting systems Injection-
moulded thermoplastics fittings Test method for visually
assessing effects of heating
prEN 802, Plastics piping and ducting systems Injection-
moulded thermoplastics fittings for pressure piping systems
Test method for maximum deformation by crushing
prEN 804, Plastics piping systems Injection-moulded socket
fittings for solvent-cemented joints for pressure piping
Test method for resistance to a short-term internal
hydrostatic pressure
THERMAL SPRAYING
prEN 657, Thermal spraying Terminology, classification
(Introduction)
Public Review list
LOTUS
Organization: Lotus Development Corp.
800 El Camino Real West
Mountain View, CA 94040
Contact: Edward I. Owens Director of Technology Industry
Relations
PHONE: 415-335-6646 FAX: 415-960-0840
e-mail: eowens@ccmail.com X400:
/g=edward/s=owens/p=ccmail/a=telemail/c=us
Public review: December 1, 1993, to March 2, 1994
JCPENNEY
Organization: JCPENNEY Co., Inc.
12700 Park Central Pl, Dallas, TX 75251
Contact: Dennis Teubner MGR of NCD
PHONE: 214-591-7623 FAX: 214-591-7758
Public review: November 3, 1993, to February 2, 1994
NOTE: Challenged alphanumeric names are underlined. The
Procedures for Registration provide for a challenge process,
which follows in brief. For complete details, see Section
6.4 of the Procedures.
A challenge is initiated when a letter from an interested
entity is received by the Registration Coordinator. The
letter shall identify the alphanumeric organization name
being challenged and state the rationale supporting the
challenge. A challenge fee shall accompany the letter.
After receipt of the challenge, the alphanumeric
organization name shall be marked as challenged in the
Public Review list. The Registration Coordinator shall take
no further action to register the challenged name until the
challenge is resolved among the disputing parties.
(Introduction)
Public Review list
ADMD Names
INFONET
Organization: Infonet Services Corporation
2100 E. Grand Avenue, Box 1022
El Segundo, CA 90245-1022
Contact: Carol Campen Computer Scientist
PHONE: 310-335-2600 FAX: 310-335-2876
e-mail: c=us/a=infonet/p=notice/o=infonet/s=murrell
Public review: August 25 to November 24, 1993
PRMD Names
JCP
Organization: JCPenney Co., Inc.
12700 Park Central Place
Dallas, TX 75251-1503
Contact: Dennis Teubner Mgr. Information Systems
PHONE: 214-591-7623 FAX: 214-591-7758
Public review: December 1, 1993, to March 3, 1994
CSW
Organization: Central and South West
P.O. Box 660164, Dallas, TX 75266-0164
Contact: Steve Bell Telecommunications Planner
PHONE: 214-777-1485 FAX: 214-777-2888
Public review: November 3, 1993, to February 2, 1994
SNC
Organization: Southern Company Services
64 Perimeter Center East, BIN 112, Atlanta, GA 30346
Contact: Gina Garner Network Planning
Phone: 404-668-4296 FAX: 404-668-4243
e-mail: c=US/a=ATTMAIL/p=SOUTHERN/o=SCS/s=GARNER/g=GINA/I=E
Public review: September 8 to December 7, 1993
NOTE: Challenged MHS-MD names are underlined. The Operating
Guidelines provide for a challenge process, which follows in
brief. For complete details, see Section 6.4 of the
Operating Guidelines.
A challenge is initiated when a letter from an interested
entity is received by the Registration Coordinator. The
letter shall identify the MHS-MD name being challenged and
state the rationale supporting the challenge. A challenge
fee shall accompany the letter. After receipt of the
challenge, the MHS-MD name shall be marked as challenged in
the Public Review list. The Registration Coordinator shall
take no further action to register the challenged name until
the challenge is resolved among the disputing parties.
CALL FOR COMMENT
(Introduction)
Canada: Foods and Food Additives
NOTE: The following 5 regulations pertain to regulations for
the labeling of certain foods and for the acceptable levels
of certain food additives.
TBT notification number: 93.362
Proposes amendments to the food and drug regulations
concerning vinclozolin in beans.
Final comment date: December 16, 1993
Proposed date of adoption: Not stated
TBT notification number: 93.363
Proposes amendments to the food and drug regulations
concerning lentils; rapeseed (canola); liver and kidneys of
cattle, goats, hogs, poultry, and sheep; beans; and
potatoes.
Final comment date: December 16, 1993
Proposed date of adoption: Not stated
TBT notification number: 93.364
Provides manufacturers with a new source for protease and
the opportunity to produce additional products of benefit to
consumers.
Final comment date: December 16, 1993
Proposed date of adoption: Not stated
TBT notification number: 93.365
Provides a source of chymosin B apart from the sources of
chymosin A and rennet currently on the market.
Final comment date: December 16, 1993
Proposed date of adoption: Not stated
TBT notification number: 93.366
Proposes amendments to the food and drug regulations to
allow for more specific labeling for cheese.
Final comment date: November 1, 1993
Proposed date of adoption: Not stated
Netherlands: Fishery Products
Regulates equipment and materials used in the fish retail
trade.
TBT notification number: 93.360
Final comment date: October 15, 1993
Proposed date of adoption: October 15, 1993
Netherlands: Flower Bulbs
Concerns the standards for ditylenchus destructor (eelworm)
as it relates to flower bulbs.
TBT notification number: 93.359
Final comment date: October 15, 1993
Proposed date of adoption: October 15, 1993
Republic of Korea: Inspection Criteria I
Changes inspection criteria for the following items: buoyant
material for farming marine products, electromagnetic
interference filter, aromatic bottles, vacuum bottles and
coolers, glass washer fluid for automobiles, engine anti-
freeze, coolants and corrosion inhibitors for engine
coolant, domestic pressure pans and posts, and in-line
roller skates.
TBT notification number: 93.367
Final comment date: December 21, 1993
Proposed date of adoption: January 21, 1993
Accredited Sponsors Using the Canvass Method
Book Cloth Council (BCC)
The Book Cloth Council (BCC) has applied to ANSI for
accreditation under the canvass method with following scope:
Requirements and test procedures for seven groups of plain
finished book cloths and buckrams that are impregnated or
starch filled and are used in the bookbinding industry for
book covers.
To request further information or offer comments, please
contact: Albert H. Clayburgh, Chairman, Book Cloth Council,
c/o Book Manufacturer's Institute, 45 William Street,
Wellesley, MA 02181. Comments should be submitted by
December 26, 1993, with a copy to the Secretary, Executive
Standards Council, at ANSI Headquarters.
Initiation of Canvasses
The following organizations have announced their intent to
conduct canvasses on the proposed American National
Standards listed in order to develop evidence of consensus
for submittal to ANSI. Directly and materially affected
interests wishing to participate in these canvasses should
contact the sponsors within 30 days of the publication of
this issue.
Air-Conditioning and Refrigeration Institute
4301 North Fairfax Drive, Suite #425
Arlington, VA 22203
Contact: Henry Hwong
ARI 1110-92, Mechanical Transport Refrigeration Units
Underwriters Laboratories, Inc.
333 Pfingsten Road, Northbrook, IL 60062-2096
Contact: Fred Alroth
UL 1207, Sewage Pumps for Use in Hazardous Locations
(revision of ANSI/UL 1207-1987)
Contact: Steve Chiu
UL 858, Household Electric Ranges (revision of ANSI/UL 858-
1986)
Contact: Alan McGrath
UL 1812, Ducted Heat Recovery Ventilators (new standard)
UL 1815, Nonducted Heat Recovery Ventilators (new standard)
Contact: Hetal Patel
UL 410, Slip Resistance of Floor Surface Materials (new
standard)
U.S. Technical Advisory Groups
U.S. TAG to ISO/TC 29/SC 9 Tools with Cutting Edges Made
of Hard Cutting Materials
The Cemented Carbide Producers Association (CCPA) has
applied for approval and accreditation of the U.S. TAG to
ISO/TC 29/SC 9 Tools with Cutting Edges Made of Hard
Cutting Materials. The TAG will operate under the Model
Operating Procedures for U.S. Technical Advisory Groups to
ANSI for ISO Activities as found in Annex A of the ANSI
Procedures for U.S. Participation in the International
Standards Activities of the ISO
To request further information or offer comments, please
contact: Mr. Jeffrey Wherry, CCPA, 30200 Detroit Road,
Cleveland, OH 44145-1967. Comments should be submitted by
December 26, 1993, with a copy to the Secretary, Executive
Standards Council, at ANSI Headquarters.
U.S. TAG to ISO/TC 35/SC 14 Anti-Corrosive Paint Systems
for Steel Structures
NACE International has applied for administratorship and
accreditation of the U.S. TAG to ISO/TC 35/SC 14 Anti-
Corrosive Paint Systems for Steel Structures. The TAG will
operate under the Model Operating Procedures for U.S.
Technical Advisory Groups to ANSI for ISO Activities as
found in Annex A of the ANSI Procedures for U.S.
Participation in the International Standards Activities of
the ISO
To request further information or offer comments, please
contact: Ms. Pam Huddle, NACE International, P.O. Box
218340, Houston, TX 77218-8340 Comments should be submitted
by December 26, 1993, with a copy to the Secretary,
Executive Standards Council, at ANSI Headquarters.
U.S. TAG to ISO/TC 184/SC 4 Industrial Data and Global
Manufacturing Programming Languages
The U.S. Product Data Association has applied for
accreditation of the U.S. TAG to ISO/TC 184/SC 4
Industrial Data and Global Manufacturing Programming
Languages. The TAG has developed its own operating
procedures, which are available for public review and
comment.
To request the TAG's procedures, or further information, or
to offer comments, please contact: Ms. Nancy Flower, U.S.
Product Data Association, c/o NCGA, 2722 Merrilee Drive,
Suite 200, Fairfax, VA 22031. Comments should be submitted
by January 26, 1994, with a copy to the Secretary, Executive
Standards Council, at ANSI Headquarters.
MEETING NOTICES
Board of Standards Review
The next meeting of the Board of Standards Review will be
held on Thursday December 2, 1993 at 10:00 AM in the
Conference Room at ANSI Headquarters.
Task Group on Metric Implementation
The ExSC Task Group on Metric Implementation will meet on
Thursday, December 16, 1993, at 10:00 am, at ANSI
Headquarters. For further information, please contact Kayla
Serotte, Task Group Secretary, at ANSI Headquarters.
PROJECT INITIATION NOTIFICATION SYSTEM (PINS)
ANSI Procedures require notification of ANSI by accredited
standards developers of the initiation and scope of new
activities expected to result in candidate American National
Standards and of initiation of new activities related to
revision, reaffirmation, or withdrawal of American National
Standards. This information is a key element in planning
and coordinating American National Standards.
Following is a list of proposed new American National
Standards or revisions to existing American National
Standards that have been received from standards developers
using the PINS Form. Directly and materially affected
interests wishing to receive more information should contact
the standards developer directly within sixty days of the
date of this publication.
AIHA Z9.XX, Design of Exhaust Systems and Ventilation for
Dry Grinding, Polishing and Buffing (new standard)
Contact: Ronald L. Karbowski
Norton Company
1 New Bond Street
Worcester, MA 01615-0008
ASCE/SFPE Fire Conditions Standards, (1) Standards
Calculation Methods for Equivalent Fire Resistance. (2)
Standard Rational Fire Design Procedure. (3) Standards for
Computer Model Analysis and Design of Structures for Fire
Conditions (new standard)
Structural Composites and Plastics Standards, Develop
Standards for Structural Composites and Plastics (new
standard)
Contact: Ashvin A. Shah
American Society of Civil Engineers
345 East 47th Street
New York, NY 10017
AMERICAN NATIONAL STANDARDS
Attn: A. Brenig
120 Wall Street, 32nd Floor
New York, NY 10005-3993
Send comments (with copy to BSR) to: Same