Driver Lines for LMSI CD-ROM and Sound Card Combinations

Why does the CD-ROM fail to load as I boot up the system?

Many times a CD-ROM drive is failing to work because the lines in the AUTOEXEC.BAT or CONFIG.SYS files are set incorrectly. This may be caused by:

• the drivers loading the incorrect address location for the CD-ROM.
• the drivers loading duplicate CD-ROM drives.
• the driver lines not loading at all.
• the driver lines loading in the wrong location within the AUTOEXEC.BAT or CONFIG.SYS files.

To see if the lines in your AUTOEXEC.BAT and CONFIG.SYS match what Gateway uses for its defaults, you need to view the contents of these files. To do this, at the C:\>: prompt, type:

type 

followed by the name of the file (i.e. CONFIG.SYS or AUTOEXEC.BAT). Then compare the lines in those files with the default lines found in the sections below. Try matching the lines up but make sure that you only have one set of lines in the files. If you find differences between the way the lines read in your files and the way that the lines are in the following sections, you need to edit these files individually to make the changes. To do this, at the C:\>: prompt, type:

edit autoexec.bat

and press Enter. Modify the file, press the ALT key to highlight the word FILE at the top of the screen. Press the F key to bring down the File Menu. Press the X key to exit, and then press the Y key to save the changes. This exits you to the C:\>: prompt. Next type:

edit config.sys

and press Enter. Modify the file, press the ALT to highlight the word FILE at the top of the screen. Press the F key to bring down the File Menu. Press the X key to exit, and then press the Y key to save the changes. This exits you to the C:\>: prompt. Reboot the system for the changes you made to take effect.

If you did not find any of the lines referring to your CD-ROM or sound card as listed in the following sections, the drivers may not be loaded on your system. You need to refer to your Userís Guide and follow the instructions on how to load the drivers. Once the drivers are reloaded, compare the lines again and make any modifications necessary. Always make sure that the jumper or switch settings match the settings in the AUTOEXEC.BAT and CONFIG.SYS files. Consult your Userís Manual for the different switch and jumper settings. The manual will also tell you what the specific switch settings are within the AUTOEXEC.BAT and CONFIG.SYS files.

Some special considerations when using the following sections: If there are lines listed in any section seperated by the word OR in bold letters your system file should match up with only one of those possibilities. The words that are highlighted within the line are the names of the directories where the drivers are stored. There are other lines in the CONFIG.SYS and AUTOEXEC.BAT files that do not pertain to the CD-ROM or sound card. DO NOT delete or modify any lines other than the ones pertaining to the CD-ROM or sound card.

LMSI on interface card only:

CONFIG.SYS

LASTDRIVE=E
Device=C:\DEV\DD250.SYS  /D:MSCD001 /C:99 /M:06 /I:5 /P:340
		OR
Device=C:\CDROM\ DD250.SYS  /D:MSCD001 /C:99 /M:06 /I:5 /P:340
		OR
Device=C:\DEV\ DD260.SYS  /D:MSCD001 /C:99 /M:06 /I:5 /P:340
		OR
Device=C:\CDROM\ DD260.SYS  /D:MSCD001 /C:99 /M:06 /I:5 /P:340

AUTOEXEC.BAT

C:\BIN\MSCDEX.EXE /D:MSCD001 /M:08 /L:D /V
		OR
C:\DOS\MSCDEX.EXE /D:MSCD001 /M:08 /L:D /V
		OR
C:\CDROM\MSCDEX.EXE /D:MSCD001 /M:08 /L:D /V

LMSI and Gateway 16MVL

CONFIG.SYS

LASTDRIVE=E
Device=C:\G2KAUDIO\DD260.SYS /D:MVCD001 /F:1
Device=C:\G2KAUDIO\JAZZ.SYS P220 I5 D1 E5 T330 Q2
		OR
Device=C:\MVAUDIO\DD260.SYS /D:MVCD001 /F:1
Device=C:\MVAUDIO\JAZZ.SYS P220 I5 D1 E5 T330 Q2
		OR
Device=C:\JAZZ\DD260.SYS /D:MVCD001 /F:1
Device=C:\JAZZ\JAZZ.SYS P220 I5 D1 E5 T330 Q2

AUTOEXEC.BAT

SET BLASTER=A220 D1 I5 H5 T4
C:\G2KAUDIO\MSCDEX.EXE /D:MVCD001 /M:12 /V
		OR
C:\MVAUDIO\MSCDEX.EXE /D:MVCD001 /M:12 /V
		OR
C:\JAZZ\MSCDEX.EXE /D:MVCD001 /M:12 /V

LMSI and Sound Blaster 16

(Purchased before Nov. 1994) CONFIG.SYS

LASTDRIVE=E
Device=C:\CDROM\DD250.SYS /D:MSCD001 /C:99 /M:06 /I:11 /P:340
Device=C:\SB16\DRV\CSP.SYS /P:220

AUTOEXEC.BAT

C:\BIN\MSCDEX.EXE /D:MSCD001 /M:08 /L:D
		OR
C:\DOS\MSCDEX.EXE /D:MSCD001 /M:08 /L:D	
		OR
C:\CDROM\MSCDEX.EXE /D:MSCD001 /M:08 /L:D
SET BLASTER=A220 I5 D1 H5 P330 T6
SET SOUND=C:\SB16
C:\SB16\SB16SET /M:220 /VOC:220 /CD:220 /MIDI:220 /LINE:220 /TREBLE:0
C:\SB16\SBCONFIG.EXE /S

The information in these articles is provided "as-is" without warranty of any kind, and all warranties are hereby disclaimed, whether express or implied, including, without limitation, the implied warranties of merchantability, fitness for a particular purpose and non-infringement. Gateway 2000 will not be liable for any damages whatsoever, whether direct, special, indirect, incidental, or consequential (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or any other pecuniary loss) arising out of, or related to your use of, or inability to use the information in any such article, even if advised of the possibility of such damages. Because some states and jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you. You may not further distribute, reproduce, rent, sell, transfer or license these articles.

If our documentation hasn't helped you,
this might be a good time to send
an e-mail to Technical Support.

Copyright © 1996 Gateway 2000 Inc. All rights reserved.
Please see our Legal Information. Please send feedback to Webmaster Central.